INDUSTRY CASTING SOLUTIONS
Drawing-based cast components for tractors, harvesters, seeders and agricultural machinery, with attention to repeatable interfaces, practical materials and field durability.
此处放：拖拉机 / 收割机 + 变速箱壳体、轮毂、支架组合图；作用：说明农业整机与铸件应用关系；建议比例 16:10
01 / FEATURED CAST COMPONENTS
Product cards connect the industry use case to an existing product route or a focused RFQ discussion.
02 / PRODUCT CATEGORIES
Product categories organize the search around the function and equipment interface instead of a random list of products.
Housings and interfaces around transmission, axle and gearbox systems.
Castings for mounting, support and field-serviceable machine structures.
Components where geometry, machinability and sealing or bearing interfaces are reviewed together.
03 / TYPICAL APPLICATIONS
Use the equipment or system closest to your project to find a focused starting point.
Powertrain and chassis castings for repeated field cycles, service access and consistent fit.
Components around drive, support and hydraulic systems where repeatability helps assembly and maintenance.
Drawing-based parts for frames, supports and functional assemblies attached to agricultural equipment.
Cast bodies and housings for selected pumps, valves and material-handling equipment.
04 / MATERIALS FOR THIS INDUSTRY
Material families shown here are starting points. Exact grades, treatment and documentation are confirmed against the customer specification.
A cost-conscious option for housings and covers where damping, machinability and dimensional stability are key considerations.
Typical applicationsTransmission housings · Covers · General machinery castingsA balanced choice for housings, hubs and structural interfaces requiring strength, toughness and practical machining.
Typical applicationsAxle housings · Wheel hubs · Bearing housingsUsed for selected brackets, wear-facing parts and structural castings after loading and heat-treatment requirements are confirmed.
Typical applicationsBrackets · Supports · Wear components05 / RECOMMENDED CASTING PROCESSES
Only processes relevant to this industry are shown. Final selection depends on geometry, material, quantity and required quality.
Housings, hubs and medium-to-large agricultural castings
Selected housings and parts needing more mould detail
Complex housing geometry
06 / CUSTOM CASTING CAPABILITIES
Send the information already available. The team can then confirm the manufacturing route, missing inputs and the useful basis for quotation.
Review drawing revisions, critical dimensions and the information needed for a manufacturable route.
Use available 3D data to discuss geometry, tooling and machining references.
Start with a sample, photo or equipment reference when a drawing is not yet available.
Confirm material, hardness and application requirements before quotation.
Match product references, fitment and customer identification requirements.
Align tooling, sample review and repeat production around the confirmed project scope.
07 / MACHINING & SECONDARY OPERATIONS
Secondary operations are reviewed according to the drawing, application and agreed delivery condition.
Process and material selection starts from the component geometry and application.
→Application-matched heat treatment is discussed where the confirmed material and part require it.
→Machining requirements, datum references and fit-critical dimensions are reviewed with the drawing.
→Cleaning, shot blasting and other finishing requirements are confirmed per part.
→The inspection plan is aligned with material, geometry, application and customer requirements.
→Identification and packing are agreed around part protection, labeling and shipment requirements.
08 / QUALITY & INSPECTION
Inspection methods and records are selected according to the confirmed customer specification. The listed checks are discussion points, not blanket claims for every part.
Material grade and required documentation are checked against the agreed specification.
Hardness requirements are confirmed for parts where wear or fit performance depends on them.
Critical dimensions, interfaces and machining references are checked against the drawing.
Surface condition, casting appearance and finishing requirements are reviewed before packing.
09 / HOW WE MANUFACTURE YOUR CASTINGS
Melting, molding, pouring, finishing, machining and inspection are connected into a project-specific route.
11 / FAQ
We can review housings, hubs, brackets, supports, covers and selected pump or valve castings according to the equipment model and project information.
Yes. Send the drawing, 3D model, sample or equipment reference so the material, casting route and machining requirements can be discussed.
OEM batch production can be discussed after the drawing revision, tooling basis, sample approval points and required inspection records are confirmed.
Machining can be included when the drawing defines the required datums, tolerances and fit-critical surfaces.
Grey iron and ductile iron are common discussion options for housings; cast or alloy steel can be reviewed when loading or wear requirements call for it.
A 2D drawing, 3D model, existing sample, equipment model, estimated quantity and application details are useful starting inputs.
REQUEST A QUOTE
Send us your drawing, material requirement, quantity and application. Our team will review the project and recommend a suitable manufacturing route.
